WARRANTY PERIOD

Your Cuta-Copter comes with a One Year Limited Warranty against defects in materials and/or workmanship for consumer use only, excluding rental or commercial use. For all Australian consumers, our warranty is not intended to limit a consumer’s rights under the Competition and Consumer Act 2010.

The warranty period is effective for all original Cuta-Copter’s from the date the product is purchased from an authorised Cuta-Copter Australian dealer, to the original purchaser, for a period of 12 months within Australia and New Zealand.

LIABILITY

To the maximum extent permitted by law, this warranty does not cover claims or liability for any incidental or consequential damages arising from, or in connection to the product.

The user accepts all liability and responsibility for the safe operation of the craft and undertakes to only operate the craft when they are competent in the operation of the craft and adhere to all local laws and regulations.

Once you have used this product, it is deemed that you have fully understood the contents of the manual and the warranty coverage. In the event of improper setup and/or use of the product, Cuta Copter Australia will not accept any liability for damages or compensation.

LIMITED WARRANTY COVERAGE

Exclusions

  1. damage caused from normal wear and tear, accident, improper/misuse of the product, sunlight, penetrative water due to collision, unless caused due to defective materials or workmanship.
  2. damage caused by negligence or lack of adherence to the manual and the recommended servicing/maintenance for the product.
  3. damage caused by altering the Flight Controllers factory settings or parameters. Alterations include but are not limited to any changes to the Flight Controllers settings and parameters without the express written authority by Cuta-Copter Australia. The flight controller records all changes to settings and parameters in addition to full flight history – ‘Black box’.
  4. consumable parts including propellers, landing gear, batteries unless the failure was due to defects in materials or workmanship of the product.
  5. damage caused by pilot error not related to product failure.
  6. damage caused by external influences such as, but not limited to loss of GPS signal, electromagnetic interference from natural ground anomalies, transmission towers, power lines, sub stations, radio towers etc
  7. damage caused from transmission interference and other wireless devices.
  8. damage caused by unauthorised modifications to the product by a non- authorised Cuta Copter repairer.
  9. damage caused by using the product outside the products specifications/limitations and/or continuing to use the product in an impaired or damaged state.
  10. damage caused due to operating the product with a damaged or defective battery and or damage caused due to failure or consequential damage due to improper use/maintenance/storage of the battery.
  11. any product that does not have a serial number, if the serial number has been removed or altered, and the purchaser cannot provide proof of purchase.
  12. Non recovery of drone

REGISTER YOUR WARRANTY

Please visit cutacopteraustralia.com.au and register your warranty as soon as you have purchased the Cuta-Copter.

How to make a claim under

Please visit cutacopteraustraliacom.au and accept the warranty/service conditions and complete the warranty claim form.
Please print the claim form generated and send it along with the drone (At your expense) to the service address listed on the claim form. Please ensure the drone is correctly packaged within the original case and it is packaged sufficiently to reduce any damage during transit. It is advised you adequately insure the goods and retain all shipping documents.

Warranty Procedure

On receipt of the product Cuta Copter Australia will inspect and test the product to determine the issue and responsibility of the product. If it is deemed the issue/problem is covered under warranty, Cuta Copter will be responsible for the inspection fee, materials, labour, and freight costs.

If it is determined that the issue/problem is not covered by the warranty, an inspection fee will be charged, and a quote will be provided prior to any work or maintenance being carried out. The costs of all materials, labour and freight will be the responsibility of the product owner.

Please contact us at any time regarding any service or warranty query directly [email protected]

Scroll to Top

TRIDENT BOSS+ Propulsion System

High capacity 6S LiPo Battery
40A Electronic Speed Controllers ‘ESC’
High thrust waterproof motors
15” High quality carbon fibre propellers

Advanced Flight Modes

ALT/Hold mode
POS/Hold mode (Anti Pendulum Mode)
Loiter Mode
Follow me mode
Return to Land mode
Come to me mode
GPS Waypoint mission planning
Click to Save – GPS position saved

AIRCRAFT

Waterproof Level: Waterproof seal on main electronics chamber
Surface Buoyant: Level 2 Flotation
Drone Weight: 1780g (without battery)
Dimensions: 455mm x 455mm
Max Ascend Speed: 10m/s
Max Descend Speed: 3m/s
Max Flight Speed: 65kph (User Adjustable)
Max Flight Altitude: 40M – Set at factory
Wind Rating Typical Maximum: 40kph (21-22Knots)
Wind Rating Peak Gusts: 50kph(26-27 Knots)
Max Flight Time (per charge): 4 drops at 300M, 700gm bait, (Max load – 1 drop to 700 meters)
Max Flight Range: 3 km – (Geofence set to 700M)
Max Payload Capacity: 4.5KG (Recommended safe lifting weight 4.0KG)
ESC: 40A sealed in waterproof dielectric resin
Propellers: 15” carbon fibre propellers
Working Temperature: -10°C ~ 40°C
APP: SkyDroid GCS (Android Only)
Motor: Brushless/Waterproof

GPS

MAIN: CUAV Neo 3 -Ublox M9N satellite receiver. Enables simultaneous reception of 4 Global Navigation Satellite Systems ‘GNSS’ – GPS, Galileo, GLONASS and BeiDouh.
BACKUP: Industrial grade RM3100 compass!

FLIGHT CONTROLLER

Type: NORA+ (PX4)
Microcontroller: STM32H7
Processor: 32 Bit Arm® Cortex®-M7, 480MHz, 2MB flash memory, 1MB RAM
Sensors: 3 x Accelerometers, 3 x Gyroscopes, Magnetometer, 2 x Barometers

REMOTE CONTROL

Weight: 660g
Frequency: 2.400-2.483GHz
Range: 3 km (unobstructed, free of interference) Set at factory to 700M
Modulation: New FHSS
Working Current: 100mAh
No. of Channels: 10
Battery: 2 X 18650 Lithium batteries (Provided)
Video Transmission
Range: 3 km Max (unobstructed, free of interference)
Working current: 180mA
Camera: 720P HD 1280×720

VIDEO TRANSMISSION

Range: 3 km Max (unobstructed, free of interference)
Working current: 180mA
Camera: 720P HD 1280×720 DIGITAL

STANDARD BATTERY (6S/5000MAH 22.2 LIPO)

Standard Battery (6S/5000MAH 22.2V 60C LiPo)
Battery Type: LiPo
Battery weight:743gms
Operating Temp: -10̊ to 50̊C
Charging Current: 5AMP
Voltage: 22.2V

Charger

Type: 100W Smart Balance Charger LiPo
Battery Charge Time: 60mins at 30% level

TRIDENT T5K V2+ PROPULSION SYSTEM

High capacity 6S LiPo Battery
40A Electronic Speed Controllers ‘ESC’
High thrust waterproof motors
15” High quality carbon fibre propellers

Advanced Flight Modes

ALT/Hold mode
POS/Hold mode (Anti Pendulum Mode)
Loiter Mode
Follow me mode
Return to Land mode
Come to me mode
GPS Waypoint mission planning
Click to Save – GPS position saved

AIRCRAFT

Waterproof Level: Waterproof seal on main electronics chamber
Surface Buoyant: Level 2 Flotation
Drone Weight: 1720g (without battery)
Dimensions: 455mm x 455mm
Max Ascend Speed: 10m/s
Max Descend Speed: 3m/s
Max Flight Speed: 65kph (User Adjustable)
Max Flight Altitude: 40M – Set at factory
Wind Rating Typical Maximum: 40kph (21-22Knots)
Wind Rating Peak Gusts: 50kph(26-27 Knots)
Max Flight Time (per charge): 5-6 drops at 300M, 700gm bait
Max Flight Range: 3 km – (Geofence set to 700M)
Max Payload Capacity: 3.5KG (Recommended safe lifting weight 3.0KG)
ESC: 40A Sealed in waterproof Di-electric resin
Propellers: 15” carbon fibre propellers
Working Temperature: -10°C ~ 40°C
APP: SkyDroid Tower (Android Only)
Motor: Brushless/Waterproof

GPS

MAIN GPS: CUAV Neo 3 -Ublox M9N satellite receiver. Enables simultaneous reception of 4 Global Navigation Satellite Systems ‘GNSS’ – GPS, Galileo, GLONASS and BeiDouh.

BACKUP: Industrial grade RM3100 compass.

FLIGHT CONTROLLER

Type: NORA+ (PX4)
Microcontroller: STM32H7
Processor: 32 Bit Arm® Cortex®-M7, 480MHz, 2MB flash memory, 1MB RAM
Sensors: 3 x Accelerometers, 3 x Gyroscopes, Magnetometer, 2 x Barometers

REMOTE CONTROL

Weight: 660g
Frequency: 2.400-2.483GHz
Range: 3 km (unobstructed, free of interference) Set at factory to 700M
Modulation: New FHSS
Working Current: 100mAh
No. of Channels: 10
Battery: 2 X 18650 Lithium batteries (Provided)

VIDEO TRANSMISSION

Range:3 km Max (unobstructed, free of interference)
Working current: 180mA
Camera: 720P HD 1280×720 DIGITAL

STANDARD BATTERY (6S/6800MAH 22.2V LIPO)

Battery Type: LiPo
Battery weight: 805gms
Operating Temp: -10̊ to 50̊C
Charging Current: 5AMP
Voltage: 22.2V

Charger

Type: 100W Smart Balance Charger LiPo
Battery Charge Time: 60mins at 30% level

AIRCRAFT

Waterproof Level: IP67 canopy on main electronics chamber
Surface Buoyant: Level 2 Flotation
Drone Weight: 1720g (without battery)
Dimensions: 455mm x 455mm
Max Ascend Speed: 10m/s
Max Descend Speed: 3m/s
Max Flight Speed: 65kph (User Adjustable)
Max Flight Altitude: 40M – Set at factory
Wind Rating Typical Maximum: 40kph (21-22Knots)
Wind Rating Peak Gusts: 50kph(26-27 Knots)
Max Flight Time (per charge): 4-5 drops at 250M, 700gm bait
Max Flight Range: 1.5km – Geofence set to 500M
Max Payload Capacity: 3.0KG (Recommended safe lifting weight 2.5KG)
ESC: 40A
Propellers: 15” carbon fibre propellers
Working Temperature: -10°C ~ 40°C
APP: SkyDroid Tower (Android Only)
Motor: Brushless/Waterproof

GPS

Concurrent reception of up to 3 Global Navigation Satellite Systems ‘GNSS’
Communication and acquisition of 4 GNSS platforms – GPS, Galileo, GLONASS and BeiDouh.

FLIGHT CONTROLLER

Type: Pixhawk mini
Processor: Advanced 32 Bit Arm® Cortex®-M4 Processor running NuttX RTOS
Sensors: IMU MPU9250 and ICM20608
PMU: PM06 V2

REMOTE CONTROL

Weight: 660g
Frequency: 2.400-2.483GHz
Range: 1.5km (unobstructed, free of interference) Set at factory to 500M (user adjustable)
Modulation: New FHSS
Working Current: 100mAh
No. of Channels: 10
Battery: 2 X 18650 Lithium batteries (Provided)

VIDEO TRANSMISSION

Range: 1.5km Max (unobstructed, free of interference)
Working current: 180mA
Gimbal: 1 AXIS
Camera: 720P HD 1280×720

STANDARD BATTERY (6S/5000MAH 22.2V LIPO)

Battery Type: LiPo
Battery weight: 651gms
Operating Temp: -10̊ to 50̊C
Charging Current: 5AMP
Voltage: 22.2V

Charger

Type: 100W Smart Balance Charger LiPo
Battery Charge Time: 60mins at 30% level

AIRCRAFT

Waterproof Level: IP67 on main Chamber

Surface Buoyant: Level 2 Flotation
Drone Weight: 1739g (without battery)
Dimensions: 355mm x 355mm
Max Ascend Speed: 10m/s
Max Descend Speed: 3m/s
Max Flight Speed: 65kph (User Adjustable)
Max Flight Altitude: 40M – Set at factory
Wind Rating Typical Maximum: 40kph (21-22Knots)
Wind Rating Peak Gusts: 50kph(26-27 Knots)
Max Flight Time (per charge): 23 minutes no load
Max Flight Range: 1.5km – Geofence set to 500M
Max Payload Capacity: 2.5KG (Recommended safe lifting weight 2KG)
ESC: 40A – sealed in di-electric resin
Propellers: 13” carbon fibre propellers
Working Temperature: -10°C ~ 40°C
APP: SkyDroid Tower (Android Only)
Motor: Brushless/Waterproof

GPS

Concurrent reception of up to 3 Global Navigation Satellite Systems ‘GNSS’ – GPS, Galileo, GLONASS and BeiDouh

FLIGHT CONTROLLER

Type: Pixhawk 4 mini
Processor: 32 Bit Arm® Cortex®-M7, 216MHz, 2MB memory, 512KB RAM
Sensors: 2 x Accelerators, 2 x Gyro’s, Magnetometer, Barometer
PMU: PM06 V2

REMOTE CONTROL

Weight: 660g
Frequency: 2.400-2.483GHz
Range: 1.5km (unobstructed, free of interference) Set at factory to 500M (user adjustable)
Modulation: New FHSS
Working Current: 100mAh
No. of Channels: 10
Battery: 2 X 18650 Lithium batteries (Provided) 20 hours flight time

VIDEO TRANSMISSION

Range: 1.5km Max (unobstructed, free of interference)
Working current: 180mA
Camera: 720P HD 1280×720

STANDARD BATTERY (6S 6800mAh 22.2V LIPO)

Battery Type: LiPo
Battery weight: 821gms
Operating Temp: -10̊ to 50̊C
Charging Current: 5AMP
Voltage: 22.2V

Charger

Type: 100W Smart Balance Charger LiPo
Battery Charge Time: 90mins

AIRCRAFT

Waterproof Level: IP67 on main electronics chamber
Surface Buoyant: Level 2 Flotation
Drone Weight: 1720g (without battery)
Dimensions: 455mm x 455mm
Max Ascend Speed: 10m/s
Max Descend Speed: 3m/s
Max Flight Speed: 65kph (User Adjustable)
Max Flight Altitude: 40M – Set at factory
Wind Rating Typical Maximum: 40kph (21-22Knots)
Wind Rating Peak Gusts: 50kph(26-27 Knots)
Max Flight Time (per charge): 5-6 drops at 300M, 700gm bait
Max Flight Range: 1.5km – Geofence set to 500M
Max Payload Capacity: 3.0KG (Recommended safe lifting weight 2.5KG)
ESC: 40A
Propellers: 15” carbon fibre propellers
Working Temperature: -10°C ~ 40°C
APP: SkyDroid Tower (Android Only)
Motor: Brushless/Waterproof

GPS

Concurrent reception of up to 3 Global Navigation Satellite Systems ‘GNSS’
Communication and acquisition of 4 GNSS platforms – GPS, Galileo, GLONASS and BeiDouh.

FLIGHT CONTROLLER

Type: Durandal (PX4)
Microcontroller: STM32H7
Processor: 32 Bit Arm® Cortex®-M7, 480MHz, 2MB flash memory, 1MB RAM
IO Processor: 32 Bit Arm® Cortex®-M3, 24MHz, 8KB SRAM
Sensors: 2 x Accelerometers, 2 x Gyroscopes, Magnetometer, Barometer
PMU: PM06 V2

REMOTE CONTROL

Weight: 660g
Frequency: 2.400-2.483GHz
Range: 1.5km (unobstructed, free of interference) Set at factory to 500M (user adjustable)
Modulation: New FHSS
Working Current: 100mAh
No. of Channels: 10
Battery: 2 X 18650 Lithium batteries (Provided)

VIDEO TRANSMISSION

Range: 1.5km Max (unobstructed, free of interference)
Working current: 180mA
Gimbal: 1 AXIS
Camera: 720P HD 1280×720

STANDARD BATTERY (6S/6800MAH 22.2V LIPO)

Battery Type: LiPo
Battery weight: 651gms
Operating Temp: -10̊ to 50̊C
Charging Current: 5AMP
Voltage: 22.2V

Charger

Type: 100W Smart Balance Charger LiPo
Battery Charge Time: 60mins at 30% level